Working Principle

The working principle of the latest generation of Wuxi Shengmei spray humidifier is that the water is pressurized by the humidifier host and then sprayed by a special nozzle, the sprayed water mist and air for heat and humidity exchange to achieve the purpose of humidification of the air.

This humidification method belongs to the enthalpy humidification method, in the humidification at the same time can also play a certain cooling effect, it has the advantages of energy saving, safety, reliability, etc., has a very high cost performance ratio.

Main specifications

Performance features

 * Integrated operation: Integrated system processing, increased reliability, improved operational stability, safety, and ease of maintenance.

 * Spraying reliable: the use of imported transparent water filter, fully solve the impact of water quality problems.

 * Simple operation: The host is equipped with temperature and humidity automatic inspection system, temperature and humidity adjustment are automatically completed by the system, safe and reliable operation, truly unmanned management. Directly powered by water pressure, no need for air compressor and other auxiliary equipment.

——Good atomization effect, particle diameter is only 3-5 microns.

——When you stop humidification, the system automatically drains the remaining water in the pipeline to prevent scaling.

——Simple installation, easy operation, minimal maintenance work, and unmanned system operation.

——The precision-machined back-splash type micro-mist nozzle has good abrasion resistance and no dripping.

——The system is equipped with a water cut-off protection system for stable and reliable operation.

Applicable fields

• Industry: humidification of textile factory, cigarette factory, electronic factory, printing factory, automobile painting factory, wood (furniture) processing factory, fire (explosives) production factory, etc.; cooling of power plant factory, steel plant factory, etc.; humidification and cooling or disinfection of high temperature and high humidity environmental conditions in brewing and food industry.
  Agriculture: cold storage, greenhouse sheds, livestock breeding, flower nurseries, edible fungus cultivation and other humidification, cooling spraying, fertilization, etc.
  Landscape creation: the ultra-fine fog particles suspended in the air like clouds moving with the wind, sometimes hidden, creating a fascinating landscape effect; at the same time, the ultra-fine fog particles contain a large number of negative ions, increasing the oxygen content of the air, greatly creating and improving the environment for people to live and live.
  
• 
  

Product use and maintenance

1、After opening the box, check the packing list one by one, attach the spare parts and documents to be kept properly.
2、Inject L-AN46~68 (old brand 30#~40#) mechanical oil into the pump to 1/2 position.
3、Check whether the nuts and screws at each linkage are loose.
4、Move the machine to the workplace and check carefully whether the power supply meets the requirements.
5、The machine working pressure 5-6Mpa is appropriate, if there are special requirements, the machine can also be raised to 7Mpa, but as far as possible to reduce the machine in the high pressure state of long-term operation, the pressure adjustment in the injection state.
6、After 50 hours of use, the oil must be replaced in the new machine. When the oil is released, the bottom screw is removed to release the oil in the pump, followed by the injection of new oil, which is very important to extend the service life of the machine. In the cumulative use to 300 hours and then replace the oil with the same method, after every 300-500 hours to replace the oil.
7, long-term use or low winter temperatures, the host high-pressure pump should be drained of water, the method is to close the water inlet valve, while disconnecting the host outlet, turn on the dehydration run for about half a minute. Then loosen the end of a nozzle to drain the water left in the high-pressure pipe to prevent the pipeline from freezing.

Common faults and troubleshooting

This equipment if there are other failures please contact us: 13196538895

Notes:
1, inverter settings see the random inverter manual, note: the relevant parameters of the inverter has been set before the factory, non-professionals please do not adjust.
2、The time control switch and time relay can be adjusted and set by the customer according to the actual equipment use, see the manual of the random time control switch and time relay for the setting method.

After-sales guarantee

Safety rules

1、The machine must be checked before use to supply power, while according to the safety of electricity regulations, the power must be installed leakage protection switch.
2、The machine must be safely grounded when in use, be sure to use a good grounded socket with it, and must cut off the power when not in use.
3、Prevent the power cord from touching the heat source, oil, sharp knife edge, etc. Do not place the power cord at the intersection, so as not to damage the wire and dangerous.
4、The user must cut off the power supply before maintenance and repair.
5、Such as motor, electrical failure, the user must ask professional maintenance personnel to repair, in order to avoid danger.
6、It is strictly prohibited to be operated by children and untrained people.
7、The pump is not fueled, idling is strictly prohibited.
8、The machine uses room temperature water, the water temperature should not exceed 45℃. In 45℃ or lower environment, pay attention to freeze protection.
9、When the power supply line or important parts of the equipment are damaged, it is prohibited to use the equipment.
10、Usually, the working pressure has been adjusted at the factory, so please do not adjust it by yourself.
11、In order to ensure the safe use of the equipment, should use the original parts provided by our factory or approved.
12、The nozzle must use the matching nozzle provided by our factory.
13、The user must use the machine according to the above "rules", if you violate the above "rules" requirements, then all the consequences are their own responsibility.

Previous: SM-1816 High pressure spray host    Next: DRS-06A Ultrasonic Humidifier